SC Spectre 3.0 Ardus Limited Edition

Integrated Liquid Cooling Features:
Reservoir, D5 Pump Top, D5 Pump Cover, Fill Port, Drain Port, roughly half of the cooling loop.

Integrated Cable Management Features:
Cable management channels with cable combs. 3x 8pin EPS on the left side of motherboard and up to two above the 24pin. 24pin Cable. SATA Data x2.
6x PCIE go through the PSU Top Shroud.

Reduced build time due to integration:
With the pump and reservoir combo and roughly half of the loop integrated there is less assembly to be done. Also, less fittings and tube are needed.
Cable management is also quicker, just clip your cables into the integrated cable combs and they are all perfectly aligned.

Integration Cost Component:
A large portion of the case cost is due to the integration. These are components you do not have to purchase for your build. The pump and reservoir combo, less fittings, less tube, no cable combs, or cable management components.

Compatibility:
Theoretically the more integration the less compatibility. For Spectres integration the position of each integrated port and cable routing hole was carefully chosen based on statistics and our experience.

Integration & Optimization:
With the integration we did not just develop a case, we also had to develop all the integrated components. This meant that we could focus more on optimization than would normally be possible. The integrated loop routes in Spectre allow for more flow than 16mm tubes.
The pump top was designed for the D5 pump, maximizing flow to and from the distribution plate.
The reservoir was designed to remove air as quickly as possible making the loop easier to fill.
The fill port is at the highest point on the back for the case and the drain point at the lowest point.
The cable channels and combs are designed for 4mm sleeved cables. They can be clipped in very quickly and there is far less work to do for clean cable management.

High End Components:
Spectre 3.0 fits XL-ATX motherboards and has 8 expansion slots. It is designed for fit up to two RTX 3090s. It can fit the largest PSUs up to 220mm. For the cooling system it can fit 2x 360mm radiators 60mm thick with a single set of fans or 2x 360mm radiators 40mm thick with two sets of fans, and the powerful D5 pump.

Radiator Adjustment:
The radiator mounts have a large range of adjustment to help with port alignment to the distribution plate.

Storage:
Spectre 3.0 has 6x 2.5” Drive positions. Two are on the top of the PSU shroud and there are four inside of the PSU shroud. The two on top of the PSU shroud cannot be used with vertically mounted GPUs.

Every component of Spectre is CNC machined from a solid block of material. With the level of transparency and being an open case, we wanted it to be a celebration of the raw materials. There is no hidden or back side, and this also goes for the components being installed. Due to this we selected the most high-end materials manufacturing process. The Distribution Plate is machined on a CNC router built from thick sheets of cast acrylic. It is hand assembled with silicone gaskets and stainless-steel fasteners, and pressure tested. The metal components are machined with Extreme Precision from solid blocks of 6061 aluminum on a CNC mill then sand blasted and anodized.

We are all experienced system builders at Singularity Computers having built high end water-cooled systems for over 15 years. Our approach to product development begins with a need for our own builds and so the origin is always function. From there we start to build ideas around this function and the aesthetics and everything else follows. The original idea for Spectre came from our years of building highly customized, high end water-cooled systems and trying to reduce the exceptionally long build times and complexity. Our approach to development is very hands on, we are doing real world testing every day.
The aesthetics of Spectre originate from its function with one of the main aesthetic features (the lighting) being something only made possible by the integration. We wanted the case to look skeletal and almost transparent enough to (in a way) disappear around the components. The metal components have been designed to enhance this with an extreme focus on detailed and complex multi sided CNC machining.

Water-cooling Integration: Reservoir, Pump Top, Pump Cover, Fill Port, Drain Port, Part of cooling loop.
Ports: x6 G1/4” BSPP. 1x Fill Port. 1x Drain Port.
Pump: (Not included): Compatible with all D5 pumps.
LED Strips: 5 integrated ARGB LED Strips, 1 in the distribution plate, 1 in the PSU shroud and 3 in the case panels.
Motherboard Form Factor: XL-ATX (Up to: 285mm Wide & 343.5mm High).
E-ATX, ATX, Mini-DTX, Mini-ITX.
Expansion Slots: x8.
Case Form Factor: Mid Tower.
Package Dimensions: L: 640mm W: 620mm H: 110mm (Case comes flat packed).
Package Weight: 19kg.
Case Dimensions: L: 545mm H: 595mm W: 254mm.
Case Weight: 16kg.
Storage: 6x 2.5”. 4 can be used at the same time. 2 are on top of the PSU shroud and cannot be used with vertically mounted GPUs. 4 are inside of the PSU Shroud.
Radiators: 360mm x 60mm with 1 set of standard 25mm fans or 360mm x 40mm with 2 sets of standard 25mm fans.
Maximum GPU Length: 500mm.
Maximum GPU Height: 170mm in standard orientation. Unlimited in vertical orientation.
Maximum CPU Cooler Height: 170mm.
Maximum PSU Length: 230mm (Space allowed for cables).
Front Panel I/O: No Front I/O. Vandal Switch 16mm. White LED.
Vertical GPU Mount: x1 included. (2nd Vertical GPU Available Separately). Vertical GPU Ribbon Cable 280mm: PCIE 3.0.
Vertical GPU Slot Spacing: x3 Slots (60mm).
Materials: 6061 Aluminum Anodized. Cast Acrylic. Stainless Steel.
Manufacturing Process: CNC Mill, CNC Router.
Assembly: Distribution Plate Assembled by Hand. Metal Components need to be assembled by the customer.
Testing: All Distribution Plates are factory pressure tested.

Spectre 3.0 Ardus Limited Edition Case: x1

• Integrated Components:
  • Reservoir: x1.
  • Pump Top: x1.
  • Pump Cover: x1.
  • Fill Port: x1.
  • Drain Port: x1.
  • Cable Combs: x1.
• Hex Keys:
  • M3: x1
  • M4: x1.
  • M6: x1.
• Microfiber Cloth: x1.
• Stop Fittings: x2.
• 5v ARGB LED Strip: x5.
• 6mm Clear Cast Acrylic Side Panel Window: x1.
• Vertical GPU Mount: x1.

NVIDIA GeForce:
GeForce Garage – MetallicAcid’s Battlefield 2042 Build

Tom’s Hardware:
Singularity Computers’ Spectre Case Has A Water Cooling Distribution Plate

Gamebyte:
Post Malone Unveils His Insane $6,400 Gaming PC 

Jayztwocents:

The parts needed to complete my personal rig arrived!
We are professionals… professional IDIOTS!
Personal Gaming Rig Update… this is going to be a challenge WORTH the effort!
I finally picked a case for my personal build… but I have to assemble it!
Build log intro 1 – Post Malone – Musician turned PC Gamer
Build log intro 2 – Post Malone reacts to his Custom PC Concepts!
Build log intro 3 – Post Malone – Beerbongs and Bentleys Custom PC Case!
Post Malone Build Log Part 1 – This is the craziest build I’ve done yet
Post Malone Build Log Part 2 – EVERYTHING IS GOING WRONG!
Post Malone Build Log Part 3 – It’s ALMOST done! But why is it taking so long??
Post Malone Build Log Part 4 – Post Malone FINALLY gets his Custom Beerbongs & Bentleys Gaming PC!

Paul’s Hardware:
Build log part 1 – This Build is RIDICULOUS… But There’s a Problem 
Build log part 2 – The Most Important Part of a Water Cooled PC Build
Build log part 3 – Filled the Loop, Forgot the Motherboard
Build log part 4 – I’ve Never Put This Much Thought Into a Build Before
Build log part 5 – My SECRET WEAPON for Hardline Custom Water Cooling!
Build log part 6 – I Can’t Believe It’s (Almost) Finished!
Build log part 7 – The Most BEAUTIFUL Computer I’ve Ever Built!

LinusTechTips:
Spectre – A See-Through PC Case??

AK-Mod at Computex 2018 with G-Skill & Intel:
Gskill Gold Shovel build#05 Singularity Cases Spectre

PCJunkieMod:
This Is NOT a Review!! User Feedback WANTED!!!!!
Custom Newegg and Intel giveaway PC! Day 1
Custom Newegg and Intel giveaway PC! Day 2
Custom Newegg and Intel giveaway PC! Day 3

Newegg Studios:
The Newegg and Intel Legendary PC Giveaway