Singularity Computers Wraith 2.0 Volta is a whole new approach to computer case design. With Spectre we introduced water-cooling system integration in the form of a distribution plate which replaced the entire rear wall of the case, we used similar ideas on Wraith 2.0. With the Singularity Computers PowerBoard we have introduced electronics integration, essentially it is a distribution plate but for cables. Wraith 2.0 is now split into two versions, one which has our water-cooling cooling integration and Volta which has PowerBoard Integration. The PowerBoard on Wraith 2.0 Volta is fully integrated replacing the entire rear wall of the case similar to the distribution plate on Wraith 2.0. Behind it are two acrylic covers, one clear with laser etching and another satin black cover. The PowerBoard integrates the 24pin and 8pin EPS, PWM & ARGB Hubs, direct connect SATA 2.5” and 3.5”. It also has integrated ARGB LEDs around the perimeter and under the motherboard, a touch activated power button, power and reset buttons and an on off switch for the ARGB LEDs. The PowerBoard reduces cable clutter meaning there is more space for liquid cooling components and loop building. Volta fits a high-end water-cooled cooled system with 2x 240mm radiators, the largest GPUs, any size SFX-L PSU and pump and reservoir.There are two PSU locations depending on the configuration you prefer, the rear PSU location allows larger pump/reservoir combos to be used and the front PSU position allows more 3.5” drives to be installed.
Cables & Adaptors:
Custom hand built MDPC-X PowerBoard cables with a large range of sleeve colours available here
PowerBoard Cables are available here
SC Shift Adaptors are available here
Note: Motherboards with 90 degree 24pin, EPS and/or 6pin PCIE supplementary power connections will require SC Shift Adaptors for clean cable routing.
Note: D5 Pump not included.
24pin x1. EPS x2. PWM x4. ARGB x 7. SATA 2.5” x4. SATA 3.5” x2 (removes x2 2.5” when used).
Touch activated Power Button.
Power & Reset Buttons.
LED on/off switch.
x37 ARGB LEDs on front side around perimeter and under motherboard.
PowerBoard Linking Cables: 24pin x1. 8pin EPS x1. 18AWG Black Headshrinkless Sleeve.
PWM Female to Female 50cm Black Sleeved x1.
ARGB Female to Female 50cm Black Sleeved x1.
Motherboard Form Factor: Mini-ITX, Mini-DTX
Case Dimensions: 407mm x 407mm x 170mm (including legs)
Package Dimensions: 450mm x 500mm x 120mm
Case Weight: 4kg
Case Packaged Weight: 5kg.
Expansion Slots: x3.
Storage: 2.5″ x5 (x2 are 2.5” or 3.5”). 3.5” x3 (2 are 2.5” or 3.5”).
PSU Compatibility: SFX, SFX-L. Unlimited Length.
Radiator Top: 240mm x30mm.
Radiator Front: 240mm x30mm.
Maximum GPU Length: 300mm.
Maximum GPU Thickness: 3 slots.
Maximum GPU Width: Unlimited.
Maximum CPU Cooler Height: 130mm.
Front Panel I/O: Vandal Switch 16mm.
Vertical GPU Mount: Included Singularity Computers PCIE 4.0 Bracket and Riser Cable.
Materials: 6061 Anodized Aluminum, Cast Acrylic, Stainless Steel.
Manufacturing Process: CNC Router, CNC Mill, CNC Lathe.
The PowerBoard is a PCB which integrates the 24pin and EPS, PWM and ARGB Hubs, direct connect SATA 2.5” and 3.5”, Power and Reset Buttons, ARGB LEDs with an on off switch and a touch activated Power Button. The PowerBoard distributes core component cables and integrates other features and functions. It is a new method for cables allowing standardization of cable lengths and making cable management no longer necessary. Wraith 2.0 Volta comes included with a standard set of black sleeved linking cables including 24pin x1 and 8pin EPS x2, the PCIE cables need to be directly connected from the PSU to the GPU.
Reduced build time due to integration:
The functionality integrated on the Powerboard means that these components don’t have to be installed separately. For example, the PWM and ARGB hubs, lighting and the direct connect SATA 2.5” and 3.5”. The need for cable management is almost completely removed by the PowerBoard.
Integration Cost Component:
A large portion of the case cost is due to the integration. These are components you do not have to purchase for your build. The Powerboard is a full solution for cables and ARGB and PWM hubs.
Integration & Optimization:
With the integration we did not just develop a case, we also developed all the integrated components. This meant that we could focus more on optimization than would normally be possible.
High End Components:
Despite its small size Wraith 2.0 Volta can fit a high-end liquid cooled build. It can fit a full-sized GPU and SFX-L PSU. It can fit x2 240mm radiators 30mm thick with a single set of fans. There is enough space for a pump and reservoir combo such as the Protium 2.0 ARGB 150 D5 Reservoir Combo. The PowerBoard reduces cable bulk allowing more space for liquid cooling components.
Two PSU Mounting Locations:
There is a PSU mounting location toward the front of the case on the bottom panel and at the back of the case on the rear panel. The main benefit of the front PSU location is you can fit an extra 3.5” HDD, and the benefit of the rear one is that you can fit larger pump/reservoir combos. It depends on your build layout and how you want it to look.
We have been building high end water-cooled systems for over 15 years. Our approach to product development begins with a need for our own builds and so the origin is always function. From there we start to build ideas around this function and the aesthetics and everything else follows. The original ideas for our products came from years of building highly customized, high end water-cooled systems and trying to reduce the exceptionally long build times and complexity. Our approach to development is hands on, we are using and testing our own products every day.
Almost all components of Wraith 2.0 Volta are CNC machined from a solid block of material with extreme precision. Everything is carefully assembled by hand and tested. Our approach and philosophy are that there is no hidden or back side, everything is on display and so the design is a celebration of the raw materials and the manufacturing processes with everything on display.
|Dimensions||450 × 500 × 120 mm|
Only logged in customers who have purchased this product may leave a review.
Questions and answers of the customers
1. what options do i have for a pump/res combo?
2. how do u route tubes to the 2 rads cpu and gpu wihtout a distro plate built in?
3. where is the manual?
4. Where are pictures of a full build full watercooled?
From the people who brought you the first ever PC Chassis liquid cooling integration, we now bring you Wraith. In development for the past 2 years since the release of Spectre, Wraith has all of the features of Spectre but in a smaller Mini-ITX Mini-DTX form factor. Now you can fit the most extreme components on the market into a very small space and have the ultimate in liquid cooling. Integrated cooling components include the Reservoir, D5 Pump Top, D5 Pump Cover, Fill Port, Drain Port and over half of the cooling loop. Integration and compatibility do not have to work against each other when you have more than a decade of experience building extreme liquid cooled systems. From a combination of statistics and experience we have created a port layout which will not inhibit compatibility or your creativity. Wraith has a cable cover so that stock cables can be used in a clean configuration, custom cables are not necessary. Despite its compact size Wraith can fit full sized GPUs, 2x 240mm radiators, 13x 2.5” drives and even a 3.5” drive and more. The case is designed to be modified and every component can be completely disassembled. As always we look forward to seeing your creativity with our design.ETA: 3 weeks x1 remaining D5 Pump not included. [gallery link="none" columns="2" size="medium" ids="20742,20602"]